module ieee802-dot1q-tsn-types {

    yang-version 1;

    namespace
      'urn:ieee:std:802.1Q:yang:ieee802-dot1q-tsn-types';

    prefix dot1q-tsn-types;

    import ietf-inet-types {
      prefix inet;
    }

    organization
      "Institute of Electrical and Electronics Engineers";

    contact
      "WG-URL: http://ieee802.org/1/
    WG-EMail: stds-802-1@ieee.org
    
    Contact: IEEE 802.1 Working Group Chair
    Postal: C/O IEEE 802.1 Working Group
           IEEE Standards Association
           445 Hoes Lane
           Piscataway
           NJ 08854
           USA
    
    E-mail: stds-802-1@ieee.org";

    description
      "Common typedefs and groupings for TSN user/network configuration in
    IEEE Std 802.1Q.
    
    Copyright (C) IEEE (2022).
    
    This version of this YANG module is part of IEEE Std 802.1Q; see the
    standard itself for full legal notices.";

    revision "2022-03-08" {
      description
        "Published as part of IEEE Std 802.1Q-2022. Second version";
      reference
        "IEEE Std 802.1Q-2022, Bridges and Bridged Networks.";

    }

    revision "2018-02-15" {
      description
        "Amendment: Stream Reservation Protocol (SRP) Enhancements and
      Performance Improvements. Initial version";
      reference
        "46.3 of IEEE Std 802.1Qcc-2018";

    }


    typedef stream-id-type {
      type string {
        pattern
          "[0-9a-fA-F]{2}"
            + "(-[0-9a-fA-F]{2}){5}"
            + ":"
            + "[0-9a-fA-F]{2}"
            + "-"
            + "[0-9a-fA-F]{2}";
      }
      description
        "This typedef specifies a Stream ID, a unique identifier of the
      Stream's configuration, used by protocols in the network to
      associate the user's Stream with TSN resources.
      
      The Stream ID is a string that represents two fields:
      
      MAC Address:
      
      A 48-bit IEEE 802 MAC address associated with the Talker sourcing
      the Stream to the bridged network. The entire range of MAC
      addresses are acceptable.
      
      NOTE 1The MAC address component of the StreamID can, but does not
      necessarily, have the same value as the source_address parameter
      of any frame in the actual data Stream. For example, the Stream ID
      can be assigned by a TSN CUC (see 46.1.3.3 of IEEE Std
      802.1Q-2022), using a pool of MAC addresses that the TSN CUC
      maintains.
      
      NOTE 2If the MAC addresses used to construct Stream IDs are not
      unique within the network, duplicate Stream IDs can be generated,
      with unpredictable results.
      
      Unique ID:
      
      A 16-bit unique ID that is used to distinguish between multiple
      Streams within the station identified by MAC Address.
      
      The string specifies eight octets, with each octet represented as
      two hexadecimal characters. The first six octets specify the MAC
      Address, using the canonical format of IEEE Std 802, with a dash
      separating each octet. The last two octets specify the Unique ID,
      with the high-order octet, a dash, and then the low-order octet.
      The MAC Address and Unique ID are separated by colon.
      
      stream-id-type is intended for use by other modules as the type
      for a key to a list of Stream configurations (using group-talker
      and group-listener) and a list of Stream status (using
      group-status-stream and group-status-talker-listener).";
      reference
        "46.2.3.1 of IEEE Std 802.1Q-2022";

    }

    grouping group-interface-id {
      description
        "This YANG grouping specifies the identification of a distinct
      point of attachment (interface) in a station (end station or
      Bridge).";
      reference
        "46.2.3.3 of IEEE Std 802.1Q-2022";

      leaf mac-address {
        type string {
          pattern
            "[0-9a-fA-F]{2}(-[0-9a-fA-F]{2}){5}";
        }
        description
          "mac-address is the unique individual MAC address (IEEE Std 802) of
        the interface in the station (end station or Bridge). This MAC
        address uniquely identifies the station within the local
        network.
        
        mac-address shall be included in an instance of a container
        using group-interface-id.
        
        NOTEThis MAC address can be discovered in the physical topology
        using protocols such as IEEE Std 802.1AB (LLDP). LLDP supports
        MAC address as a subtype for the stations Chassis ID and Port
        ID. If the station does not use MAC address for its LLDP IDs,
        remote management can be used to associate this mac-address to
        the values provided in the LLDP IDs.
        
        The string uses the hexadecimal representation specified in IEEE
        Std 802 (i.e. canonical format).";
      }

      leaf interface-name {
        type string;
        description
          "interface-name is the name of the interface that is assigned
        locally by the station (end station or Bridge).
        
        interface-name may be included in an instance of a container
        using group-interface-id.
        
        IEEE Std 802 recommends that each distinct point of attachment
        to an IEEE 802 network have its own EUI MAC address. If the
        identified station follows this IEEE 802 recommendation, the
        mac-address leaf uniquely identifies the interface as well as
        the station, and interface-name is not needed.
        
        If the mac-address applies to more than one interface (distinct
        point of attachment) within the station, interface-name provides
        a locally assigned name that can help to identify the interface.
        
        When YANG is used for management of the station, interface-name
        is the interface name that serves as the key for the stations
        interface list (RFC7223).
        
        NOTE 1The TSN CNC is typically located in a different physical
        product than the station identified by this group-interface-id.
        Since the interface-name is assigned locally by the identified
        station, it is possible that the stations product will change
        interface-name in a manner that the TSN CNC cannot detect. For
        example, RFC7223 mentions that the YANG interface name can
        change when a physical attachment point is inserted or removed.
        
        NOTE 2This interface name can be discovered in the physical
        topology using protocols such as IEEE Std 802.1AB (LLDP). LLDP
        supports interface name as a subtype for its Port ID. If the
        station does not use interface name for its LLDP Port ID, remote
        management can be used to associate this interface-name to the
        values provided in the LLDP Port ID.";
      }
    }  // grouping group-interface-id

    grouping group-ieee802-mac-addresses {
      description
        "This YANG grouping specifies the pair of IEEE 802 MAC addresses
      for Stream identification.
      
      The use of these fields for Stream identification corresponds to
      the managed objects for Stream identification in IEEE Std 802.1CB.
      If inconsistency arises between this specification and IEEE Std
      802.1CB, IEEE Std 802.1CB takes precedence.";
      reference
        "46.2.3.4.1 of IEEE Std 802.1Q-2022";

      leaf destination-mac-address {
        type string {
          pattern
            "[0-9a-fA-F]{2}(-[0-9a-fA-F]{2}){5}";
        }
        description
          "Destination MAC address.
        
        An address of all 1's specifies that the destination MAC address
        is ignored for purposes of Stream identification.
        
        The string uses the hexadecimal representation specified in IEEE
        Std 802 (i.e. canonical format).";
      }

      leaf source-mac-address {
        type string {
          pattern
            "[0-9a-fA-F]{2}(-[0-9a-fA-F]{2}){5}";
        }
        description
          "Source MAC address.
        
        An address of all 1's specifies that the source MAC address is
        ignored for purposes of Stream identification.
        
        The string uses the hexadecimal representation specified in IEEE
        Std 802 (i.e. canonical format).";
      }
    }  // grouping group-ieee802-mac-addresses

    grouping group-ieee802-vlan-tag {
      description
        "This YANG grouping specifies a customer VLAN Tag (C-TAG of clause
         9) for Stream identification.
      
      The Drop Eligible Indicator (DEI) field is not relevant from the
      perspective of a TSN Talker/Listener.
      
      The use of these fields for Stream identification corresponds to
      the managed objects for Stream identification in IEEE Std 802.1CB.
      If inconsistency arises between this specification and IEEE Std
      802.1CB, IEEE Std 802.1CB takes precedence.";
      reference
        "46.2.3.4.2 of IEEE Std 802.1Q-2022";

      leaf priority-code-point {
        type uint8 {
          range "0 .. 7";
        }
        description
          "Priority Code Point (PCP) field.
        
        The priority-code-point is not used to identify the Stream, but
        it does identify a traffic class (queue) in Bridges.";
      }

      leaf vlan-id {
        type uint16 {
          range "0 .. 4095";
        }
        description
          "VLAN ID (VID) field.
        
        If only the priority-code-point is known, the vlan-id is
        specified as 0.";
      }
    }  // grouping group-ieee802-vlan-tag

    grouping group-ipv4-tuple {
      description
        "This YANG grouping specifies parameters to identify an IPv4
      (RFC791) Stream.
      
      The use of these fields for Stream identification corresponds to
      the managed objects for Stream identification in IEEE Std 802.1CB.
      If inconsistency arises between this specification and IEEE Std
      802.1CB, IEEE Std 802.1CB takes precedence.";
      reference
        "46.2.3.4.3 of IEEE Std 802.1Q-2022";

      leaf source-ip-address {
        type inet:ipv4-address;
        description
          "Source IPv4 address.
        
        An address of all 0's specifies that the IP source address is
        ignored for purposes of Stream identification.";
      }

      leaf destination-ip-address {
        type inet:ipv4-address;
        description
          "Destination IPv4 address.";
      }

      leaf dscp {
        type uint8;
        description
          "Differentiated services code point, DSCP (RFC2474).
        
        A value of 64 decimal specifies that the DSCP is ignored for
        purposes of Stream identification.";
      }

      leaf protocol {
        type uint16;
        description
          "IPv4 Protocol (e.g. UDP).
        
        The special value of all 1s (FFFF hex) represents None, meaning
        that protocol, source-port, and destination-port are ignored for
        purposes of Stream identification.
        
        For any value other than all 1s, the lower octet is used to
        match IPv4 Protocol.";
      }

      leaf source-port {
        type uint16;
        description
          "This matches the source port of the protocol.";
      }

      leaf destination-port {
        type uint16;
        description
          "This matches the destination port of the protocol.";
      }
    }  // grouping group-ipv4-tuple

    grouping group-ipv6-tuple {
      description
        "This YANG grouping specifies parameters to identify an IPv6
      (RFC8200) Stream.
      
      The use of these fields for Stream identification corresponds to
      the managed objects for Stream identification in IEEE Std 802.1CB.
      If inconsistency arises between this specification and IEEE Std
      802.1CB, IEEE Std 802.1CB takes precedence.";
      reference
        "46.2.3.4.4 of IEEE Std 802.1Q-2022";

      leaf source-ip-address {
        type inet:ipv6-address;
        description
          "Source IPv6 address.
        
        An address of all 0's specifies that the IP source address is
        ignored for purposes of Stream identification.";
      }

      leaf destination-ip-address {
        type inet:ipv6-address;
        description
          "Destination IPv6 address.";
      }

      leaf dscp {
        type uint8;
        description
          "Differentiated services code point, DSCP (RFC2474).
        
        A value of 64 decimal specifies that the DSCP is ignored for
        purposes of Stream identification.";
      }

      leaf protocol {
        type uint16;
        description
          "IPv6 Next Header (e.g. UDP).
        
        The special value of all 1s (FFFF hex) represents None, meaning
        that protocol, source-port, and destination-port are ignored for
        purposes of Stream identification.
        
        For any value other than all 1s, the lower octet is used to
        match IPv6 Next Header.";
      }

      leaf source-port {
        type uint16;
        description
          "This matches the source port of the protocol.";
      }

      leaf destination-port {
        type uint16;
        description
          "This matches the destination port of the protocol.";
      }
    }  // grouping group-ipv6-tuple

    grouping group-user-to-network-requirements {
      description
        "This YANG grouping specifies specifies user requirements for the
      Stream, such as latency and redundancy.
      
      The network (e.g. CNC) will merge all user-to-network-requirements
      for a Stream to ensure that all requirements are met.";
      reference
        "46.2.3.6 of IEEE Std 802.1Q-2022";

      leaf num-seamless-trees {
        type uint8;
        default "1";
        description
          "num-seamless-trees specifies the number of trees that the
        network will configure to deliver seamless redundancy for the
        Stream.
        
        The value zero is interpreted as one (i.e. no seamless
        redundancy).
        
        This requirement is provided from the Talker only. Listeners
        shall set this leaf to one.
        
        From each Talker to a single Listener, the network configures a
        path that relays Stream data through Bridges. If the Talker has
        more than one Listener, the network configures a tree of
        multiple paths.
        
        num-seamless-trees specifies the number of maximally disjoint
        trees that the network shall configure from the Talker to all
        Listeners. Each tree is disjoint from other trees, in that the
        network evaluates the physical topology to avoid sharing the
        same Bridge and links in each trees paths. This computation of
        disjoint trees is maximal, in that shared Bridges and links are
        avoided to the maximum extent allowed by the physical topology.
        For example, if a single link exists from a Bridge to a
        Listener, and num-seamless-trees is 3, then all 3 trees will
        share that link to the Listener.
        
        When num-seamless-trees is greater than one, the transfer of the
        Streams data frames shall use a seamless redundancy standard,
        such as IEEE Std 802.1CB. When a link shared by multiple trees
        diverges to multiple disjoint links, the seamless redundancy
        standard replicates (i.e. forwards a distinct copy of each data
        frame to the disjoint trees). When disjoint trees converge to a
        single link, the seamless redundancy standard eliminates the
        duplicate copies of each data frame. Assuming that other sources
        of frame loss are mitigated (e.g. congestion), failure of a link
        or Bridge in one disjoint tree does not result in frame loss as
        long as at least one remaining disjoint tree is operational.
        
        If the Talker sets this leaf to one, the network may make use of
        redundancy standards that are not seamless (i.e. failure of link
        results in lost frames), such as MSTP and IS-IS.
        
        If the Talker sets this leaf to greater than one, and seamless
        redundancy is not possible in the current network (no disjoint
        paths, or no seamless redundancy standard in Bridges),
        group-status-stream.status-info.failure-code is non-zero
        (46.2.4.1 of IEEE Std 802.1Q-2022).
        
        If group-user-to-network-requirements is not provided by the
        Talker or Listener, the network shall use the default value of
        one for this leaf.";
        reference
          "46.2.3.6.1 of IEEE Std 802.1Q-2022";

      }

      leaf max-latency {
        type uint32;
        default "0";
        description
          "Maximum latency from Talker to Listener(s) for a single frame
        of the Stream.
        
        max-latency is specified as an integer number of nanoseconds.
        
        Latency shall use the definition of 3.102, with additional
        context as follows: The Known reference point in the frame is
        the message timestamp point specified in IEEE Std 802.1AS for
        various media (i.e. start of the frame). The first point is in
        the Talker, at the reference plane marking the boundary between
        the network media and PHY (see IEEE Std 802.1AS). The second
        point is in the Listener, at the reference plane marking the
        boundary between the network media and PHY.
        
        When this requirement is specified by the Talker, it must be
        satisfied for all Listeners.
        
        When this requirement is specified by the Listener, it must be
        satisfied for this Listener only.
        
        If group-user-to-network-requirements is not provided by the
        Talker or Listener, the network shall use the default value of
        zero for this leaf.
        
        The special value of zero represents usage of the initial value
        of group-status-talker-listener.accumulated-latency as the
        maximum latency requirement. This effectively locks-down the
        initial latency that the network calculates after successful
        configuration of the Stream, such that any subsequent increase
        in latency beyond that value causes the Stream to fail.
        
        The assumption for when the first point occurs in the Talker
        depends on the presence of the time-aware container in the
        Talkers traffic-specification.
        
        When time-aware is not present:
        
        The Talker is assumed to transmit at an arbitrary time (not
        scheduled).
        
        When time-aware is present:
        
        The first point is assumed to occur at the start of each
        traffic-specification.interval, as if the Talkers offsets
        (earliest-transmit-offset and latest-transmit-offset) are both
        zero. The Talkers offsets are not typically zero, but use of the
        start of interval for purposes of max-latency allows the
        Listener(s) to schedule their application independently from the
        Talkers offset configuration.
        
        The Listener determines max-latency based on its scheduling of a
        read function in the application. Nevertheless, the time from
        frame reception (i.e. second point) to execution of the read
        function is in the user scope, and therefore not included in
        max-latency.
        
        max-latency can be set to a value greater than the Talkers
        interval, in order to specify a longer latency requirement. For
        example, if the Talkers interval is 500 microsec, and
        max-latency is 700 microsec, the Listener receives the frame no
        later than 200 microsec into the interval that follows the
        Talkers interval.";
        reference
          "46.2.3.6.2 of IEEE Std 802.1Q-2022";

      }
    }  // grouping group-user-to-network-requirements

    grouping group-interface-capabilities {
      description
        "This YANG grouping specifies the network capabilities of all
      interfaces (Ports) contained in end-station-interfaces.
      
      The network may provide configuration of these capabilities in
      group-status-talker-listener.interface-configuration.
      
      NOTEIf an end station contains multiple interfaces with different
      network capabilities, each interface should be specified as a
      distinct Talker or Listener (i.e. one entry in
      end-station-interfaces). Use of multiple entries in
      end-station-interfaces is intended for network capabilities that
      span multiple interfaces (e.g. seamless redundancy).";
      reference
        "46.2.3.7 of IEEE Std 802.1Q-2022";

      leaf vlan-tag-capable {
        type boolean;
        default "false";
        description
          "When vlan-tag-capable is true, the interface supports the
        ability to tag/untag frames using a Customer VLAN Tag (C-TAG of
        clause 9) provided by the network.
        
        For a Talker, the networks tag replaces the tag specified by the
        data-frame-specification. If the data-frame-specification is
        untagged (no group-ieee802-vlan-tag), the networks tag is
        inserted in the frame as it passes through the interface.
        
        For a Listener, the users tag from the data-frame-specification
        replaces the networks tag as the frame passes through the
        interface. If the data-frame-specification is untagged (no
        group-ieee802-vlan-tag), the networks tag is removed from the
        frame as it passes through the interface.
        
        If the end station supports more than one interface (i.e. more
        than one entry in end-station-interfaces), vlan-tag-capable of
        true means that a distinct VLAN tag can be applied to each
        interface. The list of VLAN tag (one for each interface) can be
        provided by the network in
        interface-configuration.interface-list (ieee802-vlan-tag
        choice).
        
        When vlan-tag-capable is false, the interface does not support
        the capability to tag/untag frames using a Customer VLAN Tag
        (C-TAG of clause 9) provided by the network.
        
        If interface-capabilities is not provided by the Talker or
        Listener, the network shall use the default value of false for
        this leaf.";
        reference
          "46.2.3.7.1 of IEEE Std 802.1Q-2022";

      }

      leaf-list cb-stream-iden-type-list {
        type uint32;
        description
          "cb-stream-iden-type-list provides a list of the supported
        Stream Identification types as specified in IEEE Std 802.1CB.
        
        Each Stream Identification type is provided as a 32-bit unsigned
        integer. The upper three octets contain the OUI/CID, and the
        lowest octet contains the type number.
        
        NOTEIf the Talker/Listener end system supports IEEE Std 802.1CB,
        Null Stream identification is required, and that Stream
        Identification type is included in this list. If the
        Talker/Listener end system does not support IEEE Std 802.1CB,
        this list is empty.
        
        If the end station supports more than one interface (i.e. more
        than one interface-id in end-station-interfaces, an empty
        cb-stream-iden-type-list means that the end station is capable
        of transferring the Stream on any one of its interfaces (not
        all). When this is specified, the network shall decide which
        interface is best used for TSN purposes, and communicate that
        decision by returning a single interface in
        interface-configuration.interface-list. The Talker/Listener uses
        this interface alone for the Stream.
        
        If interface-capabilities is not provided within group-talker or
        group-listener, the network shall use an empty list as the
        default value for this element.";
        reference
          "46.2.3.7.2 of IEEE Std 802.1Q-2022";

      }

      leaf-list cb-sequence-type-list {
        type uint32;
        description
          "cb-sequence-type-list provides a list of the supported Sequence
        Encode/Decode types as specified in IEEE Std 802.1CB.
        
        Each sequence type is provided as a 32-bit unsigned integer. The
        upper three octets contain the OUI/CID, and the lowest octet
        contains the type number.
        
        If interface-capabilities is not provided within group-talker or
        group-listener, the network shall use an empty list as the
        default value for this element.";
        reference
          "46.2.3.7.3 of IEEE Std 802.1Q-2022";

      }
    }  // grouping group-interface-capabilities

    grouping group-interface-configuration {
      description
        "This YANG grouping provides configuration of interfaces in the
      Talker/Listener. This configuration assists the network in meeting
      the Streams requirements. The interface-configuration meets the
      capabilities of the interface as provided in
      interface-capabilities.";
      reference
        "46.2.5.3 of IEEE Std 802.1Q-2022";

      list interface-list {
        key "mac-address interface-name";
        description
          "A distinct configuration is provided for each interface in the
        Talker/Listener (even if multiple interfaces use the same
        configuration). Each entry in this interface-list consists of an
        interface identification (group-interface-id), followed by a
        list of configuration values for that interface (config-list).
        
        If interface-configuration is not provided within
        group-status-talker-listener, the network shall assume zero
        entries as the default (no interface configuration).
        
        Since the interface-name leaf is optional, empty string can be
        used for its key value.";
        uses group-interface-id;

        list config-list {
          key "index";
          description
            "List of configuration values for the interface.";
          leaf index {
            type uint8;
            description
              "This index is provided in order to provide a unique key per
            list entry. The value of index for each entry shall be
            unique (but not necessarily contiguous).";
          }

          choice config-value {
            description
              "One of the following choices is provided for each
            configuration value. Each container name acts as the case
            name for the choice.";
            container ieee802-mac-addresses {
              description
                "Source and destination MAC addresses that apply to the
              network side of the user/network boundary.
              
              NOTE 1On the userside, the MAC addresses correspond to the
              ieee802-mac-addresses of data-frame-specification.
              
              NOTE 2The source MAC address of the network is typically
              the same as the user. The destination MAC address can be
              different. For example, the user can use an individual
              address, but the network can use a group (multicast)
              address.
              
              This configuration value is not provided unless IEEE Std
              802.1CB is supported, and a value for Active Destination
              MAC and VLAN Stream identification is provided in
              cb-stream-iden-type-list of interface-capabilities.";
              reference
                "46.2.5.3.1 of IEEE Std 802.1Q-2022";

              uses group-ieee802-mac-addresses;
            }  // container ieee802-mac-addresses
            container ieee802-vlan-tag {
              description
                "Customer VLAN Tag (C-TAG of clause 9) that applies to the
              network side of the user/network boundary.
              
              NOTEOn the user side, the VLAN tag corresponds to the
              ieee802-vlan-tag of data-frame-specification (including
              untagged if this field is not provided).
              
              If the user provides a VLAN ID in the ieee802-vlan-tag of
              data-frame-specification, the Streams data frames are
              assumed to be limited to the active topology for that VLAN
              ID. Therefore, if the network uses a different VLAN ID in
              this config-value, the network shall ensure that the
              replacement VLAN ID is limited to the equivalent active
              topology.
              
              This configuration value is not provided unless
              vlan-tag-capable of interface-capabilities is true.";
              reference
                "46.2.5.3.2 of IEEE Std 802.1Q-2022";

              uses group-ieee802-vlan-tag;
            }  // container ieee802-vlan-tag
            container ipv4-tuple {
              description
                "IPv4 identification that applies to the network side of
              the user/network boundary.
              
              This configuration value is not provided unless IEEE Std
              802.1CB is supported, and a value for IP Stream
              identification is provided in cb-stream-iden-type-list of
              interface-capabilities.";
              reference
                "46.2.5.3.3 of IEEE Std 802.1Q-2022";

              uses group-ipv4-tuple;
            }  // container ipv4-tuple
            container ipv6-tuple {
              description
                "IPv6 identification that applies to the network side of
              the user/network boundary.
              
              This configuration value is not provided unless IEEE Std
              802.1CB is supported, and a value for IP Stream
              identification is provided in cb-stream-iden-type-list of
              interface-capabilities.";
              reference
                "46.2.5.3.4 of IEEE Std 802.1Q-2022";

              uses group-ipv6-tuple;
            }  // container ipv6-tuple
            leaf time-aware-offset {
              type uint32;
              description
                "If the time-aware container is present in the
              traffic-specification of the Talker, this config-value
              shall be provided by the network to the Talker.
              
              If the time-aware container is not present in the
              traffic-specification of the Talker, this config-value
              shall not be provided by the network.
              
              This config-value shall not be provided to Listeners, as
              it is not applicable.
              
              time-aware-offset specifies the offset that the Talker
              shall use for transmit. The network returns a value
              between earliest-transmit-offset and
              latest-transmit-offset of the Talkers
              traffic-specification. The value is expressed as
              nanoseconds after the start of the Talkers interval.";
              reference
                "46.2.5.3.5 of IEEE Std 802.1Q-2022";

            }
          }  // choice config-value
        }  // list config-list
      }  // list interface-list
    }  // grouping group-interface-configuration

    grouping group-talker {
      description
        "This YANG grouping specifies: - Talkers behavior for Stream
      (how/when transmitted) - Talkers requirements from the network -
      TSN capabilities of the Talkers interface(s)
      
      In the fully centralized model of TSN configuration, this grouping
      originates from the CUC, and is delivered to the CNC.";
      reference
        "46.2.3 of IEEE Std 802.1Q-2022";

      container stream-rank {
        description
          "Rank of this Stream's configuration relative to other Streams
        in the network. This rank is used to determine success/failure
        of Stream resource configuration, and it is unrelated to the
        Streams data.";
        reference
          "46.2.3.2 of IEEE Std 802.1Q-2022";

        leaf rank {
          type uint8;
          description
            "The Rank is used by the network to decide which Streams can
          and cannot exist when TSN resources reach their limit. If a
          Bridges Port becomes oversubscribed (e.g. network
          reconfiguration, IEEE 802.11 bandwidth reduction), the Rank is
          used to help determine which Streams can be dropped (i.e.
          removed from Bridge configuration).
          
          The only valid values for Rank shall be zero and one. The
          configuration of a Stream with Rank zero is more important
          than the configuration of a Stream with Rank one. The Rank
          value of zero is intended for emergency traffic, and the Rank
          value of one is intended for non-emergency traffic.
          
          NOTEIt is expected that higher layer applications and
          protocols can use the Rank to indicate the relative importance
          of Streams based on user preferences. Those user preferences
          are expressed by means beyond the scope of this standard. When
          multiple applications exist in a network (e.g. audio/video
          along with industrial control), it can be challenging for the
          varied applications and vendors to agree on multiple Rank
          values. To mitigate such challenges, this Rank uses a simple
          concept of emergency (zero) and non-emergency (one) that can
          be applied over all applications. For example, in a network
          that carries audio Streams for fire safety announcements, all
          applications are likely to agree that those Streams use Rank
          of zero.";
          reference
            "46.2.3.2.1 of IEEE Std 802.1Q-2022";

        }
      }  // container stream-rank

      list end-station-interfaces {
        key "mac-address interface-name";
        min-elements 1;
        description
          "List of identifiers, one for each physical interface (distinct
        point of attachment) in the end station acting as a Talker.
        
        Although many end stations contain a single interface, this list
        allows for multiple interfaces. Some TSN features allow a single
        Stream to span multiple interfaces (e.g. seamless redundancy).
        
        Each entry of end-station-interfaces is used by the CNC to
        locate the Talker in the topology.
        
        Since the interface-name leaf is optional, empty string can be
        used for its key value.";
        reference
          "46.2.3.3 of IEEE Std 802.1Q-2022";

        uses group-interface-id;
      }  // list end-station-interfaces

      list data-frame-specification {
        key "index";
        min-elements 1;
        description
          "data-frame-specification specifies the frame that carries the
        Talkers Stream data. The network uses the specification to
        identify this Streams frames as TSN, in order to apply the
        required TSN configuration.
        
        The specification is based on the users knowledge of the frame,
        without any network specifics. In other words, this specifies
        the frame that the Talker would use in the absence of TSN.
        
        The specification is provided as a list of fields that the user
        knows. The list is ordered from start of frame to end of header.
        For example, if the Talker uses a VLAN-tagged Ethernet frame
        (not IP), the list consists of ieee802-mac-addresses followed by
        ieee802-vlan-tag. For example, if the Talker uses a UDP/IPv4
        packet without knowledge of the Ethernet header, the list
        consists of ipv4-tuple.
        
        This list is optional, and its absence indicates that Stream
        transformation is performed in the Talker and Listeners of this
        Stream (46.2.2 of IEEE Std 802.1Q-2022).";
        reference
          "46.2.3.4 of IEEE Std 802.1Q-2022";

        leaf index {
          type uint8;
          description
            "This index is provided in order to provide a unique key per
          list entry. The value of index for each entry shall be unique
          (but not necessarily contiguous).";
        }

        choice field {
          description
            "One of the following choices is provided for each field that
          the user knows. Each container name acts as the case name for
          the choice.";
          container ieee802-mac-addresses {
            description
              "IEEE 802 MAC addresses.";
            uses group-ieee802-mac-addresses;
          }  // container ieee802-mac-addresses
          container ieee802-vlan-tag {
            description "IEEE 802.1 CTAG";
            uses group-ieee802-vlan-tag;
          }  // container ieee802-vlan-tag
          container ipv4-tuple {
            description
              "IPv4 packet identification";
            uses group-ipv4-tuple;
          }  // container ipv4-tuple
          container ipv6-tuple {
            description
              "IPv6 packet identification";
            uses group-ipv6-tuple;
          }  // container ipv6-tuple
        }  // choice field
      }  // list data-frame-specification

      container traffic-specification {
        description
          "This traffic-specification specifies how the Talker transmits
        frames for the Stream. This is effectively the Talkers promise
        to the network. The network uses this traffic spec to allocate
        resources and adjust queue parameters in Bridges.";
        reference
          "46.2.3.5 of IEEE Std 802.1Q-2022";

        container interval {
          description
            "This interval specifies the period of time in which the
          traffic specification cannot be exceeded. The traffic
          specification is specified by max-frames-per-interval and
          max-frame-size.
          
          The interval is a rational number of seconds, defined by an
          integer numerator and an integer denominator.
          
          If the time-aware container is not present, the interval
          specifies a sliding window of time. The Talkers transmission
          is not synchronized to a time on the network, and therefore
          the traffic specification cannot be exceeded during any
          interval in time.
          
          If the time-aware container is present, the interval specifies
          a window of time that is aligned with the time epoch that is
          synchronized on the network. For example, if IEEE Std
          802.1AS-2011 is used with the PTP timescale, the first
          interval begins at 1 January 00:00:00 TAI. If CurrentTime
          represents the current time, then the start of the next
          interval (StartOfNextInterval) is: StartOfNextInterval = N *
          interval where N is the smallest integer for which the
          relation StartOfNextInterval >= CurrentTime would be TRUE.";
          reference
            "46.2.3.5.1 of IEEE Std 802.1Q-2022";

          leaf numerator {
            type uint32;
            description
              "intervals numerator.";
          }

          leaf denominator {
            type uint32;
            description
              "intervals denominator.";
          }
        }  // container interval

        leaf max-frames-per-interval {
          type uint16;
          description
            "max-frames-per-interval specifies the maximum number of
          frames that the Talker can transmit in one interval.";
          reference
            "46.2.3.5.2 of IEEE Std 802.1Q-2022";

        }

        leaf max-frame-size {
          type uint16;
          description
            "max-frame-size specifies maximum frame size that the Talker
          will transmit, excluding any overhead for media-specific
          framing (e.g., preamble, IEEE 802.3 header, Priority/VID tag,
          CRC, interframe gap). As the Talker or Bridge determines the
          amount of bandwidth to reserve on the egress Port (interface),
          it will calculate the media-specific framing overhead on that
          Port and add it to the number specified in the max-frame-size
          leaf.";
          reference
            "46.2.3.5.3 of IEEE Std 802.1Q-2022";

        }

        leaf transmission-selection {
          type uint8;
          description
            "transmission-selection specifies the algorithm that the
          Talker uses to transmit this Streams traffic class. This
          algorithm is often referred to as the shaper for the traffic
          class.
          
          The value for this leaf uses Table 8-5 (Transmission selection
          algorithm identifiers) of 8.6.8 of IEEE Std 802.1Q-2022. If no
          algorithm is known, the value zero (strict priority) can be
          used.
          
          The Talkers shaping and scheduling of the Stream is considered
          to be on the user side of the user/network boundary, and this
          leaf specifies the Talkers behavior to the network.";
          reference
            "46.2.3.5.4 of IEEE Std 802.1Q-2022";

        }

        container time-aware {
          presence
            "Specifies that the Talkers traffic is synchronized to"
              + "a known time on the network (e.g. using IEEE Std 802.1AS)";
          description
            "The time-aware container provides leafs to specify the
          Talkers time-aware transmit to the network.
          
          The Talker and Listeners of a Stream are assumed to coordinate
          using user (application) mechanisms, such that each Listener
          is aware that its Talker transmits in a time-aware manner.
          
          If max-frames-per-interval is greater than one, the Talker
          shall transmit multiple frames as a burst within the interval,
          with the minimum inter-frame gap allowed by the media.
          
          NOTE: Although scheduled traffic (8.6.8.4 of IEEE Std
          802.1Q-2022) specifies a valid implementation of a time-aware
          Talker, the time-aware container is intended to support
          alternate implementations of scheduling.";
          reference
            "46.2.3.5 of IEEE Std 802.1Q-2022";

          leaf earliest-transmit-offset {
            type uint32;
            description
              "earliest-transmit-offset specifies the earliest offset
            within each interval at which the Talker is capable of
            starting transmit of its frames. As part of
            group-status-talker-listener.interface-configuration, the
            network will return a specific time-aware-offset to the
            Talker (within the earliest/latest range), which the Talker
            uses to schedule its transmit.
            
            earliest-transmit-offset is specified as an integer number
            of nanoseconds.
            
            The Talkers transmit offsets include
            earliest-transmit-offset, latest-transmit-offset, and the
            time-aware-offset returned to the Talker. Each of the
            Talkers offsets is specified at the point when the message
            timestamp point of the first frame of the Stream passes the
            reference plane marking the boundary between the network
            media and PHY. The message timestamp point is specified by
            IEEE Std 802.1AS for various media.";
            reference
              "46.2.3.5.5 of IEEE Std 802.1Q-2022";

          }

          leaf latest-transmit-offset {
            type uint32;
            description
              "latest-transmit-offset specifies the latest offset within
            the interval at which the Talker is capable of starting
            transmit ofits frames. As part of
            group-status-talker-listener.interface-configuration, the
            network will return a specific time-aware-offset to the
            Talker within the earliest/latest range), which the Talker
            uses to schedule its transmit.
            
            latest-transmit-offset is specified as an integer number of
            nanoseconds.";
            reference
              "46.2.3.5.6 of IEEE Std 802.1Q-2022";

          }

          leaf jitter {
            type uint32;
            description
              "The jitter leaf specifies the maximum difference in time
            between the Talkers transmit offsets, and the ideal
            synchronized network time (e.g. IEEE 802.1AS time). Jitter
            is specified as an unsigned integer number of nanoseconds.
            
            The maximum difference means sooner or later than the ideal
            (e.g. transmit +/- 500 nanoseconds relative to IEEE 802.1AS
            time results in jitter of 500).
            
            The ideal synchronized network time refers to time at the
            source (e.g. IEEE 802.1AS grandmaster). The jitter does not
            include inaccuracies as time is propagated from the time
            source to the Talker, because those inaccuracies are assumed
            to be known by the network, and time synchronization is a
            network technology. The jitter leaf is intended to specify
            inaccuracies in the Talkers implementation. For example, if
            the Talkers IEEE 802.1AS time is +/- 812 nanoseconds
            relative to the grandmaster, and the Talker schedules using
            a 100 microsecond timer tick driven by IEEE 802.1AS time,
            Jitter is 50000 (not 50812).
            
            The Talkers transmit offsets include
            earliest-transmit-offset, latest-transmit-offset, and the
            time-aware-offset returned to the Talker in
            group-status-talker-listener.interface-configuration.";
            reference
              "46.2.3.5.7 of IEEE Std 802.1Q-2022";

          }
        }  // container time-aware
      }  // container traffic-specification

      container user-to-network-requirements {
        description
          "user-to-network-requirements specifies user requirements for
        the Stream, such as latency and redundancy. The network (CNC)
        will merge all user-to-network-requirements for a Stream to
        ensure that all requirements are met.";
        reference
          "46.2.3.6 of IEEE Std 802.1Q-2022";

        uses group-user-to-network-requirements;
      }  // container user-to-network-requirements

      container interface-capabilities {
        description
          "interface-capabilities specifies the network capabilities of
        all interfaces (Ports) contained in end-station-interfaces.
        
        The network may provide configuration of these capabilities in
        group-status-talker-listener.interface-configuration.
        
        NOTEIf an end station contains multiple interfaces with
        different network capabilities, each interface should be
        specified as a distinct Talker or Listener (i.e. one entry in
        end-station-interfaces). Use of multiple entries in
        end-station-interfaces is intended for network capabilities that
        span multiple interfaces (e.g. seamless redundancy).";
        reference
          "46.2.3.7 of IEEE Std 802.1Q-2022";

        uses group-interface-capabilities;
      }  // container interface-capabilities
    }  // grouping group-talker

    grouping group-listener {
      description
        "This YANG grouping specifies: - Listeners requirements from the
      network - TSN capabilities of the Listeners interface(s)
      
      In the fully centralized model of TSN configuration, this grouping
      originates from the CUC, and is delivered to the CNC.";
      reference
        "46.2.4 of IEEE Std 802.1Q-2022";

      list end-station-interfaces {
        key "mac-address interface-name";
        min-elements 1;
        description
          "List of identifiers, one for each physical interface (distinct
        point of attachment) in the end station acting as a Listener.
        
        Although many end stations contain a single interface, this list
        allows for multiple interfaces. Some TSN features allow a single
        Stream to span multiple interfaces (e.g. seamless redundancy).
        
        Each entry of end-station-interfaces is used by the CNC to
        locate the Listener in the topology.
        
        Since the interface-name leaf is optional, empty string can be
        used for its key value.";
        reference
          "46.2.3.3 of IEEE Std 802.1Q-2022";

        uses group-interface-id;
      }  // list end-station-interfaces

      container user-to-network-requirements {
        description
          "user-to-network-requirements specifies user requirements for
        the Stream, such as latency and redundancy. The network (CNC)
        will merge all user-to-network-requirements for a Stream to
        ensure that all requirements are met.";
        reference
          "46.2.3.6 of IEEE Std 802.1Q-2022";

        uses group-user-to-network-requirements;
      }  // container user-to-network-requirements

      container interface-capabilities {
        description
          "interface-capabilities specifies the network capabilities of
        all interfaces (Ports) contained in end-station-interfaces.
        
        The network may provide configuration of these capabilities in
        group-status-talker-listener.interface-configuration.
        
        NOTEIf an end station contains multiple interfaces with
        different network capabilities, each interface should be
        specified as a distinct Talker or Listener (i.e. one entry in
        end-station-interfaces). Use of multiple entries in
        end-station-interfaces is intended for network capabilities that
        span multiple interfaces (e.g. seamless redundancy).";
        reference
          "46.2.3.7 of IEEE Std 802.1Q-2022";

        uses group-interface-capabilities;
      }  // container interface-capabilities
    }  // grouping group-listener

    grouping group-status-stream {
      description
        "This YANG grouping provides the status of a Streams configuration
      from the network to each user. The status in this grouping applies
      to the entire Stream (Talker and all Listeners).
      
      In the fully centralized model of TSN configuration, this grouping
      originates from the CNC, and is delivered to the CUC.
      
      The group-status-stream and group-status-talker-listener groupings
      are intended to be used by other modules within a list of status
      (state) for each Stream, with each list entry using: - leaf of
      type stream-id-type, used as key to the list - container using
      group-status-stream - container for Talker, using
      group-status-talker-listener - list for Listeners, using
      group-status-talker-listener";
      reference
        "46.2.5 of IEEE Std 802.1Q-2022";

      container status-info {
        description
          "status-info provides information regarding the status of a
        Streams configuration in the network.";
        reference
          "46.2.5.1 of IEEE Std 802.1Q-2022";

        leaf talker-status {
          type enumeration {
            enum "none" {
              value 0;
              description
                "No Talker detected.";
            }
            enum "ready" {
              value 1;
              description
                "Talker ready (configured).";
            }
            enum "failed" {
              value 2;
              description "Talker failed.";
            }
          }
          description
            "This is an enumeration for the status of the Streams Talker.";
          reference
            "46.2.5.1.1 of IEEE Std 802.1Q-2022";

        }

        leaf listener-status {
          type enumeration {
            enum "none" {
              value 0;
              description
                "No Listener detected.";
            }
            enum "ready" {
              value 1;
              description
                "All Listeners ready (configured).";
            }
            enum "partial-failed" {
              value 2;
              description
                "One or more Listeners ready, and one or more Listeners
              failed. If Talker is ready, Stream can be used.";
            }
            enum "failed" {
              value 3;
              description
                "All Listeners failed";
            }
          }
          description
            "This is an enumeration for the status of the Streams
          Listener(s).";
          reference
            "46.2.5.1.2 of IEEE Std 802.1Q-2022";

        }

        leaf failure-code {
          type uint8;
          description
            "If the Stream encounters a failure (talker-status is failed,
          or listener-status is failed, or listener-status is
          partial-failed), failure-code provides a non-zero code that
          specifies the problem. Table 46-15 of IEEE Std 802.1Q-2022
          describes each code.)";
          reference
            "46.2.5.1.3 of IEEE Std 802.1Q-2022";

        }
      }  // container status-info

      list failed-interfaces {
        key "mac-address interface-name";
        description
          "When a failure occurs in network configuration (i.e. non-zero
        failure-code in status-info), failed-interfaces provides a list
        of one or more physical interfaces (distinct points of
        attachement) in the failed end station or Bridge. Each
        identifier is sufficient to locate the interface in the physical
        topology.
        
        The failed-interfaces list is optional.
        
        Since the interface-name leaf is optional, empty string can be
        used for its key value.";
        reference
          "46.2.5.4 of IEEE Std 802.1Q-2022";

        uses group-interface-id;
      }  // list failed-interfaces
    }  // grouping group-status-stream

    grouping group-status-talker-listener {
      description
        "This YANG grouping provides the status for a specific Talker or
      Listener.
      
      In the fully centralized model of TSN configuration, this grouping
      originates from the CNC, and is delivered to the CUC.";
      reference
        "46.2.5 of IEEE Std 802.1Q-2022";

      leaf accumulated-latency {
        type uint32;
        description
          "accumulated-latency provides the worst-case maximum latency
        that a single frame of the Stream can encounter along its
        current path(s).
        
        When provided to a Listener, accumulated-latency is the
        worst-case maximum latency for that Listener only.
        
        When provided to a Talker, accumulated-latency is the worst-case
        maximum latency for all Listeners (worst path).
        
        accumulated-latency is specified as an integer number of
        nanoseconds.
        
        accumulated-latency uses the same definition for latency as
        user-to-network-requirements.max-latency.
        
        For successful status-info, the network returns a value less
        than or equal to user-to-network-requirements.max-latency.
        
        If the time-aware container is present in the
        traffic-specification of the Talker, the value is expressed as
        nanoseconds after the start of the Talkers
        traffic-specification.interval.
        
        If the time-aware container is not present in the
        traffic-specification of the Talker, the value is expressed as
        nanoseconds after the Talkers transmit of any frame in the
        Stream, at any arbitrary time.
        
        If user-to-network-requirements.num-seamless-trees is one,
        accumulated-latency shall provide the worst-case maximum latency
        for the current path from Talker to each Listener. If the path
        is changed (e.g. by a spanning tree protocol),
        accumulated-latency changes accordingly.
        
        If user-to-network-requirements.num-seamless-trees is greater
        than one, accumulated-latency shall provide the worst-case
        maximum latency for all paths configured from the Talker to each
        Listener.";
        reference
          "46.2.5.2 of IEEE Std 802.1Q-2022";

      }

      container interface-configuration {
        description
          "interface-configuration provides configuration of interfaces in
        the Talker/Listener. This configuration assists the network in
        meeting the Streams requirements. The interface-configuration
        meets the capabilities of the interface as provided in
        interface-capabilities.";
        reference
          "46.2.5.3 of IEEE Std 802.1Q-2022";

        uses group-interface-configuration;
      }  // container interface-configuration
    }  // grouping group-status-talker-listener
  }  // module ieee802-dot1q-tsn-types